Skip to content Skip to navigation menu
Loading...

SpeedCut™ Saw Chain, 16"

Part# 95TXL066G

$25.99

Added to Your Shopping Cart
Saw Chain
Product Family SpeedCut™
Pitch
?

Pitch

Chain Pitch is the size of the chain, and is defined as the distance between any three consecutive rivets divided by two. Oregon chain is made in several pitches - 1/4" is the smallest, 3/8" is the most popular, 3/4” is the largest. Pitch is important because the drive sprocket must be the same pitch as the chain, and if applicable, the bar nose sprocket. The easiest way to determine the pitch of your chain is to look at the number stamped on the drive link.
.325"
Chain Type 95TXL
Gauge
?

Gauge

Chain Gauge is the Drive Link's thickness where it fits into the bar groove. The gauge of the chain and the gauge of the bar must match. Oregon has several gauges for chainsaws - such as, .043", .050", .058" and .063". Normal wear can make it difficult to accurately measure chain gauge on a worn chain. Always order by the number stamped on the drive link of your old chain to assure correct gauge.
.050"
Drive Links
?
66
Bar Length 16"
Chain Low Kickback (ANSI)
?

Chain Low Kickback (ANSI)

Certain provisions of the safety standard known as ANSI (American National Standards Institute) B175.1 - Gasoline powered Chainsaws - Safety Requirements contain requirements designed to reduce the risk of injury from chainsaws sold in the United States. The following information should be used as a guide for the selection of appropriate replacement chains in order to maintain compliance with the ANSI B175.1 standard (United States only).
The ANSI standard B175.1 divides all chainsaw power heads into two groups:
- Under 3.8 cubic-inch (62cc) engine displacement, the chainsaw MUST meet the low kickback provisions of the standard.
- 3.8 cubic inch (62cc) and larger, the chainsaw MAY OR MAY NOT meet low kickback provisions of the standard.

Any chainsaw that does not qualify as a low kickback cutting system will bear a warning such as: “WARNING – This chainsaw is capable of severe kickback that could result in serious injury to the user. Do not operate this chainsaw unless you have extraordinary cutting needs and experience and specialized training for dealing with kickback. Chainsaws with significantly reduced kickback potential are available.Be sure to read the labels on a chainsaw before purchasing one.
When replacing chain on saws less than 3.8 cubic inches (62cc), any low-kickback chain of the proper pitch and gauge can be used. Oregon identifies and labels all low-kickback chain with green labels and all NON low kickback chain with yellow labels. Oregon safety features greatly reduce the hazard of kickback while maintaining high cutting performance. However, ALL CHAINS CAN KICKBACK, which may result in severe personal injury to the saw operator or bystander. Replacement guide bars and the ANSI standard.
The ANSI standard states:
Because of differences in replacement guide bars, the following guidelines shall be considered to determine kickback energy: Sprocket nose guide bars with the same effective length, the same number of sprocket nose teeth, and the same pitch may be considered to have equivalent kickback energy; A hard-nose guide bar having the same effective bar length, and the same or smaller nose radius as a sprocket-nose bar, may be considered to have equivalent or less kickback energy than the sprocket nose-bar; Kickback energy of all guide bar types may be considered to be less for smaller nose radius sizes.

No
Narrow Kerf Yes
File Size 3/16"
Package Type Loop

Specifications, Details & Support

Product Description

Made for arborists and property owners, the 95TXL066G SpeedCut™ Saw Chain offers top performance for saws up to 55c. This 16", .325" pitch chain features low-vibration Micro-Chisel cutters with small-radius working corners for excellent performance and easy maintenance. Oregon SpeedCut 95TXL narrow kerf cutting systems are more efficient than standard cutting systems, because they require less power from the saw. SpeedCut narrow kerf chains should always be used in conjunction with narrow kerf guide bars. This chain fits several saws including Husqvarna® 435, 445, 450, 455 Rancher and 460 Rancher.

Product Details

  • Pitch: .325", gauge: .050", narrow kerf, drive link count: 66
  • LubriTec™ keeps your chain and guide bar oiled for less friction and longer life
  • Blued Cutters deliver high-quality protection against corrosion
  • Expanded Top-Plate Filing Indicators and depth gauge filing indicators area make accurate sharpening easier
  • Exclusive OCS-01 Steel provides greater durability
  • For saw sizes 38-55 cc
  • WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov
General
Volume 1171.518 in³
Product UOM Each
Weight (with Packaging) 0.582 Lb
Support
Pro Saw Chain Warning
SpeedCut ™ System

Model Fit Guide and Parts Cross Reference

Need Help ? Contact Customer Service at +1 800-223-5168 or email us at oregonproductsupport@blount.com

Fit Guide

A-40, C-40, CP-41, CP-45, CP-540, CP-600, P-370, P-410, P-460, P-510, PRO-41, PRO-45, PRO-540, PRO-600

316.35022, 316.35085, 35201

109, 110, 111, 115, 115i, PS-460, PS-510, PS-5100S, PS-5100SH, PS-5105, PS-5105H, PS-540, PS-6100, PS-6100H

CS-3600, CS-3900, CS-4000, CS-400EVL, CS-4100, CS-440, CS-4400, CS-440EVL, CS-450, CS-4500, CS-450P, CS-4510, CS-4510, CS-4600, CS-490, CS-5000, CS-500P, CS-510, CS-520, CS-530, CS-550P

MT 4400

38568, 43177, 43178, HCS513, HCS516, HCS520, HPS513

5200

CS40EA18, CS51EAP

133, 140, 1400, 140S, 154, 1600, 234, 238, 240, 242, 242XP, 246, 254, 254XP, 257, 261, 262, 262XP, 33, 336, 338XPT, 339XP, 340, 340E, 340SE, 340SG, 345, 346, 346XP, 346XP E-TECH, 346XPG, 350, 351, 353, 353E-TECH, 353G E-TECH, 355, 357, 357XP, 357XPG, 359, 359E-TECH, 360, 362, 362 XP, 38, 40, 42, 435, 435E,
44, 440, 440E, 444, 445, 445E, 45, 450, 450 50th Anniversary, 450E, 455, 455 RANCHER, 455e RANCHER, 460, 460 RANCHER, 466, 49, 50, 51, 543XP, 543XPG, 545, 545 MARK II, 55, 55 Rancher, 550XP, 550XP MARK II, 550XPG, 550XPG MARK II, 555, 560XP, 560XPG, 57

CS46, CS52, CS56, CS62

2014, 2016, 2035, 2036, 2036 Turbo, 2040, 2040 Turbo, 2041, 2045, 2050, 2050 Turbo, 2051, 2054, 2055, 2063, 2137, 2138, 2141, 2145, 2149, 2149 Turbo, 2150, 2159, 2163, 370, 410, 420, 425, 435, 45, 450, 451, 455, 49, 50, 51, 510, 52, 520, 520SP, 521, 525, 535, CS 2135, CS 2137, CS 2138, CS 2141, CS 2145, CS 2149, CS 2149 Turbo,
CS 2150, CS 2152, CS 2152W, CS 2153, CS 2156, CS 2159, CS 2159C, CS 2159CWH, CS 2159WH, CS 2163, CS 2163WH, CS 2234, CS 2238S, CS 2240, CS 2240S, CS 2245, CS 2250, CS 2250S, CS 2252, CS 2253, CS 2253WH, CS 2255, CS 2258, CS 2260, CS 2260WH

DCS430, DCS431, DCS46018, DCS510, DCS5121, DCS5200i, DCS520i, DCS540, DCS6000i, EA5000P53G, EA6100P53E, EA6100P53G,
Makita - EA6100PREG
.325" pitch Narrow Kerf chain and guide bars must be used together for optimal performance.
EA6100PREG, EA6101P53G

MCV51R

1849AV, 2046AV, 2049AV, 46, 4600, 4700, 4900, 5000, 5500, CS 410, CS 450, MS 1846AV, MS 1849AV, MS 1850, MS 2046AV, MS 2046AVCC, MS 2049, MS 2049AV, MS 2049AVCC, MS 2050, Pro Mac 1845AV, Pro Mac 40, Silver Eagle 2818, Silver Eagle 3020, Timber Bear 20

938, 940C, 941, 945, 950, 951, 956, 962

410, 510, 540, P-360, P-400, P-450, P-500, P-5000

1074, P-21, P-26, P-28

2700, 2750, 2775, 2800, 285, 2900, 295, 3000, 305, 3050, 306 SA, 310, 3100, 315, 325, 3300, 335 Predator, 336, 4600, 4620, 4620 AV, 4620 AVHD, 4620AVX, FARM HAND (2900)

G390, G450AVS, G455AVS, G5000, G5000AVS, G5300, GZ381, GZ4350, GZ4500, GZ500, GZ5000

360, 366, 377, 400, 415, 416, 446s, 450, 451, 488, 488S, 490, 500, 502s

630, 633, 635, 636, 637, 640, 643

CS05, CS06

ECS-4000, ECS-4000B, ECS-415, ECV-4501, ECV-5601, TCS40EA, TCS51EAP

TB4620, TB4920, TB5018, TB5020, TB5518

Replacement Guide

95VP66CQ, 95VPX66CQ

501 84 06-66, 581643666, H30 66, SP33G-66

CL25066NKTL2

Related Products

No Image Available

Saw Chain Sharpening Kit, 3/16"

Saw chain sharpening kit with all the necessary components for maintaining the chain including one assembled 3/16" file guide, two wooden file handles, one 3/16" round file, one flat file and one .025" drop-center depth gauge tool.

Learn More
No Image Available

Grinder, 12V Electric Sure Sharp®

Learn More
Bar and Chain Lube, 1 Qt

Bar and Chain Lube, 1 Qt

This bar and chain lube is specially compounded to provide extra high tackiness and prevent "throw off" even under adverse weather conditions. Provides maximum engine power, low friction, and faster cutting time. High film-strength prevents wear or scuffing of chain links and bars while protecting metal parts against corrosion and rust. Resists build-up of deposits such as pitch, sap or gum.

Learn More
Black Apron Chaps, Size 40

Black Apron Chaps, Size 40

Comfortable protection for your legs while logging or using your chainsaw in apron chaps design, with 8 layers breathable warp knit chainsaw protection.

Learn More
No Image Available

Chainsaw Gloves - Size 10

Chainsaw gloves with left-hand saw protection

Learn More

Reviews

Average Customer Rating

Be the first to review this product.

Indicates required field

Rating
Back To Top