Skip to content Skip to navigation menu
Loading...

PowerCut™ Saw Chain, 20"

Part# 72LGX072G

This product is only available through retailers or servicing dealers.

Saw Chain
Product Family PowerCut™
Pitch
?

Pitch

Chain Pitch is the size of the chain, and is defined as the distance between any three consecutive rivets divided by two. Oregon chain is made in several pitches - 1/4" is the smallest, 3/8" is the most popular, 3/4” is the largest. Pitch is important because the drive sprocket must be the same pitch as the chain, and if applicable, the bar nose sprocket. The easiest way to determine the pitch of your chain is to look at the number stamped on the drive link.
3/8"
Chain Type 72LGX
Gauge
?

Gauge

Chain Gauge is the Drive Link's thickness where it fits into the bar groove. The gauge of the chain and the gauge of the bar must match. Oregon has several gauges for chainsaws - such as, .043", .050", .058" and .063". Normal wear can make it difficult to accurately measure chain gauge on a worn chain. Always order by the number stamped on the drive link of your old chain to assure correct gauge.
.050"
Drive Links
?
72
Bar Length 20"
Chain Low Kickback (ANSI)
?

Chain Low Kickback (ANSI)

Certain provisions of the safety standard known as ANSI (American National Standards Institute) B175.1 - Gasoline powered Chainsaws - Safety Requirements contain requirements designed to reduce the risk of injury from chainsaws sold in the United States. The following information should be used as a guide for the selection of appropriate replacement chains in order to maintain compliance with the ANSI B175.1 standard (United States only).
The ANSI standard B175.1 divides all chainsaw power heads into two groups:
- Under 3.8 cubic-inch (62cc) engine displacement, the chainsaw MUST meet the low kickback provisions of the standard.
- 3.8 cubic inch (62cc) and larger, the chainsaw MAY OR MAY NOT meet low kickback provisions of the standard.

Any chainsaw that does not qualify as a low kickback cutting system will bear a warning such as: “WARNING – This chainsaw is capable of severe kickback that could result in serious injury to the user. Do not operate this chainsaw unless you have extraordinary cutting needs and experience and specialized training for dealing with kickback. Chainsaws with significantly reduced kickback potential are available.Be sure to read the labels on a chainsaw before purchasing one.
When replacing chain on saws less than 3.8 cubic inches (62cc), any low-kickback chain of the proper pitch and gauge can be used. Oregon identifies and labels all low-kickback chain with green labels and all NON low kickback chain with yellow labels. Oregon safety features greatly reduce the hazard of kickback while maintaining high cutting performance. However, ALL CHAINS CAN KICKBACK, which may result in severe personal injury to the saw operator or bystander. Replacement guide bars and the ANSI standard.
The ANSI standard states:
Because of differences in replacement guide bars, the following guidelines shall be considered to determine kickback energy: Sprocket nose guide bars with the same effective length, the same number of sprocket nose teeth, and the same pitch may be considered to have equivalent kickback energy; A hard-nose guide bar having the same effective bar length, and the same or smaller nose radius as a sprocket-nose bar, may be considered to have equivalent or less kickback energy than the sprocket nose-bar; Kickback energy of all guide bar types may be considered to be less for smaller nose radius sizes.

No
Narrow Kerf No
File Size 7/32"
Package Type Loop

Specifications, Details & Support

Product Description

An ideal choice for high-production cutting, the Oregon 72LGX072G 20" PowerCut™ Saw Chain is a top performing 3/8" pitch chain. Oregon 72LGX low-vibration, full chisel cutters offer top performance. Offset depth gauges provide smoother cuts by stopping cutters from driving into the sidewall of the cut. This chain fits saws from several manufacturers including Husqvarna®, Craftsman®, Poulan®, John Deere and Jonsered®.

Product Details

  • Pitch: 3/8", gauge: .050", drive link count: 72
  • LubriTec™ keeps your chain and guide bar oiled for less friction and longer life
  • Blued Cutters deliver high-quality protection against corrosion
  • Top-Plate Filing Indicators make accurate sharpening easier
  • Exclusive OCS-01 Steel provides greater durability
  • For saw sizes 50-100 cc
General
Volume 1105.108 in³
Product UOM Each
Weight (with Packaging) 0.811 Lb
Support
Pro Saw Chain Warning

Model Fit Guide and Parts Cross Reference

Need Help ? Contact Customer Service at +1 800-223-5168 or email us at oregonproductsupport@blount.com

Fit Guide

35098,
Craftsman - 358.35098
For use with Aftermarket guide bars.
358.35098

CS5720

109, 112, 113, 114, 116, 116si, 117, 118, 119, 120, 122, 123, 133, 143, 144, 152, 153, 166, CA, PS-460, PS-510, PS-5100S, PS-5100SH, PS-5105, PS-5105H, PS-540, PS-6000i, PS-6100, PS-6100H, PS-6400, PS-6400H, PS-6400W, PS-7300, PS-7300H, PS-7300W, PS-7310, PS-7310H, PS-7900, PS-7900H, PS-7900W, PS-7910, PS-7910H, PS-7910W, PS-7910XD, PS-9010, PS-9010FL, PS9000

156, 165, 181, 956, 962, MT 6500, MT 7200, MT 8200

1100, 160, 162, 181, 185, 2100, 2101, 254, 254XP, 257, 260, 261, 262, 262XP, 266, 268, 272, 281, 285, 288, 288XP Lite, 298, 3120, 3120XP, 355, 357, 357XP, 357XPG, 359, 359E-TECH, 360, 362, 362 XP, 365, 371, 372, 372XP, 372XPG, 372XPW, 380, 385, 385XP, 385XPG, 385XPW, 390XP, 390XPG, 390XPW, 394, 394XP, 395,
395XP, 395XPG, 395XPW, 455, 455 RANCHER, 455e RANCHER, 460, 460 RANCHER, 465 Rancher, 466, 480, 51, 55, 55 Rancher, 555, 560XP, 560XPG, 562XP, 562XPG, 565, 565, 57, 570, 572XP, 572XPG, 575XP, 575XPG, 575XPW, 576XP, 576XP Auto Tune, 576XPG, 576XPW, 61, 65, 66, 70, 77, JUNGLE 3120, L Series

CS71, CS81

2051, 2054, 2055, 2063, 2065, 2071, 2077, 2083, 2083II, 2094, 2095, 2159, 2163, 2165, 2171, 490, 520, 520SP, 525, 535, 590, 625, 630, 630 Super, 630 West Coast, 670, 670 West Coast, CS 2050, CS 2050 Turbo, CS 2054, CS 2156, CS 2159, CS 2159C, CS 2159CWH, CS 2159WH, CS 2163, CS 2163WH, CS 2165, CS 2166, CS 2171, CS 2171WH, CS 2172, CS 2172WH, CS 2186, CS 2186WH, CS 2188, CS 2255, CS 2258, CS 2260, CS 2260WH

DCS430, DCS431, DCS46018, DCS510, DCS5121, DCS5200i, DCS520i, DCS540, DCS6000i, DCS6401, DCS6421, DCS6800i, DCS7301, DCS7901, DCS9000, DCS9010FL, EA5000P53G, EA5600F, EA6100P53E, EA6100P53G, EA6101P53G, EA7300P, EA7900P

MCV51R

1655, 2055, 550, 650, 7000, P100, P55, P65, P70, P85, R-11, R-12, R-14, R-16, R-17, R-18, R-19, R-20, R-21, R-22, R-23, R-30, R-35, R-40, R-416, R-420, R-421, R-435, R-440, S-50, S-55, S-65

1072, 1073, 515, 970, Farmlite, Farmsaw, Farmsaw II, P-11, P-20, P-25, P-285, P-38, P-39, P-41, P-42, P-45, P-50, P-51, P-52, P-60, P-61, P-62

405, 415, 425, 445, 455, 475, 505, 525, 655,
Poulan - PP5020AV
For use with Aftermarket guide bars.
PP5020AV, PR5020

G390, G450AVS, G455AVS, G5000, G5000AVS, G5300, GZ4350, GZ500, GZ5000, GZ550, GZ7000

550, 575, 577, 680, 695, 757, 757C, 757W

603, 613, 614, 631, 632, 634, 638, 639, 641, 644, 645, 647, 650, 651, 651SP, 652, 654, 656, 662, 665, 667, 670, 675, 680, 681, 690, 694

026, 026 PRO, 026P, 028, 028 Super, 029, 030, 031, 032, 034, 034 SUPER, 036, 036 PRO, 036 QS, 038, 038 Super MAGNUM, 039, 040, 041, 042, 044, 044 MAGNUM, 045, 046, 046 MAGNUM, 048, 056, 056 SUPER, 064, 066, 066 MAGNUM, E15, E20, E220, MS 260, MS 260 Pro, MS 261, MS 261 C-M, MS 261 C-MQ, MS 261 CQ, MS 270, MS 270 C, MS 270 C-B, MS 270 CQS, MS 290, MS 291, MS 291 C-BEQ, MS 310, MS 311, MS 341,
MS 360, MS 360 C, MS 360 Pro, MS 360 QS, MS 361, MS 361 C-B, MS 361 QS, MS 362, MS 362 C-M, MS 362 C-MQ, MS 362 CQ, MS 362 RC-M, MS 390, MS 391, MS 440, MS 440 MAGNUM, MS 441, MS 441 C, MS 441 C-M, MS 441 C-MQ, MS 441 RC-M, MS 460, MS 460 MAGNUM, MS 461, MS 650, MS 660, MS 660 MAGNUM, MS 661 C-M, MS 661 R C-M, MSE 220, MSE 250 C

Replacement Guide

501 84 26-72, 591129972, H47-72

33RS72E

CL85072NSTL2

Related Products

Saw Chain Sharpening Kit, 7/32"

Saw Chain Sharpening Kit, 7/32"

Saw chain sharpening kit with all the necessary components for maintaining the chain including one assembled 7/32" file guide, two wooden file handles, one 7/32" round file, one flat file and one .025" drop-center depth gauge tool.

Learn More
No Image Available

Grinder, 12V Electric Sure Sharp®

Learn More
No Image Available

Bar and Chain Lube, 1 Gallon

This bar and chain lube is specially compounded to provide extra tackiness and prevent "throw off" even under adverse weather conditions. Provides maximum engine power, low friction, and faster cutting time. High film-strength prevents wear or scuffing of chain links and bars while protecting metal parts against corrosion and rust. Resists build-up of deposits such as pitch, sap or gum.

Learn More
Black Apron Chaps, Size 40

Black Apron Chaps, Size 40

Comfortable protection for your legs while logging or using your chainsaw in apron chaps design, with 8 layers breathable warp knit chainsaw protection.

Learn More
No Image Available

Chainsaw Gloves - Size 10

Chainsaw gloves with left-hand saw protection

Learn More

Reviews

Average Customer Rating

Be the first to review this product.

Indicates required field

Rating
Back To Top