Guide Bar and Chain Combo, 14"

Part# 105699

$46.68

Find Servicing Dealer

Quantity

Added to Your Shopping Cart

Quick Links:

Specifications, Details & Support Model Fit Guide Accesories Category Related Products Other Products From Oregon Similar Reviews

Bar/Chain Combos
Product Family	AdvanceCut™
Chain Type	91PX
Pitch ? Pitch Chain Pitch is the size of the chain, and is defined as the distance between any three consecutive rivets divided by two. Oregon chain is made in several pitches - 1/4" is the smallest, 3/8" is the most popular, 3/4” is the largest. Pitch is important because the drive sprocket must be the same pitch as the chain, and if applicable, the bar nose sprocket. The easiest way to determine the pitch of your chain is to look at the number stamped on the drive link.	3/8" Low Profile™
Gauge ? Gauge Chain Gauge is the Drive Link's thickness where it fits into the bar groove. The gauge of the chain and the gauge of the bar must match. Oregon has several gauges for chainsaws - such as, .043”, .050"", .058” and .063"". Normal wear can make it difficult to accurately measure chain gauge on a worn chain. Always order by the number stamped on the drive link of your old chain to assure correct gauge.	.050"
Bar Length	14"
Drive Links ? Drive Links The length of your chain is determined by counting the number of drive links in your chain. Your drive link count has a direct correlation to your bar’s length. Be careful; a bar made by Oregon may take a different drive link count than that of another producer. Here’s a tip: count the number of drive links in the chain you have now, and write that number down someplace where you can find it. Or, if you have an Oregon chain in an Oregon box, the drive link count is stamped on the flap; you can save that flap for future reference.	52
Chain Low Kickback (ANSI) ? Chain Low Kickback (ANSI) Certain provisions of the safety standard known as ANSI (American National Standards Institute) B175.1 - Gasoline powered Chainsaws - Safety Requirements contain requirements designed to reduce the risk of injury from chainsaws sold in the United States. The following information should be used as a guide for the selection of appropriate replacement chains in order to maintain compliance with the ANSI B175.1 standard (United States only). The ANSI standard B175.1 divides all chainsaw power heads into two groups: - Under 3.8 cubic-inch (62cc) engine displacement, the chainsaw MUST meet the low kickback provisions of the standard. - 3.8 cubic inch (62cc) and larger, the chainsaw MAY OR MAY NOT meet low kickback provisions of the standard. Any chainsaw that does not qualify as a low kickback cutting system will bear a warning such as: “WARNING – This chainsaw is capable of severe kickback that could result in serious injury to the user. Do not operate this chainsaw unless you have extraordinary cutting needs and experience and specialized training for dealing with kickback. Chainsaws with significantly reduced kickback potential are available.Be sure to read the labels on a chainsaw before purchasing one. When replacing chain on saws less than 3.8 cubic inches (62cc), any low-kickback chain of the proper pitch and gauge can be used. Oregon identifies and labels all low-kickback chain with green labels and all NON low kickback chain with yellow labels. Oregon safety features greatly reduce the hazard of kickback while maintaining high cutting performance. However, ALL CHAINS CAN KICKBACK, which may result in severe personal injury to the saw operator or bystander. Replacement guide bars and the ANSI standard. The ANSI standard states: Because of differences in replacement guide bars, the following guidelines shall be considered to determine kickback energy: Sprocket nose guide bars with the same effective length, the same number of sprocket nose teeth, and the same pitch may be considered to have equivalent kickback energy; A hard-nose guide bar having the same effective bar length, and the same or smaller nose radius as a sprocket-nose bar, may be considered to have equivalent or less kickback energy than the sprocket nose-bar; Kickback energy of all guide bar types may be considered to be less for smaller nose radius sizes.
Narrow Kerf	No
Intenz ? Intenz Intenz guide bars have our patented Intenz chain tensioning mechanism built right into the bar itself. Replace a Intenz guide bar with another Intenz guide bar to maintain the saw’s ability to properly tension the saw chain.	No
Guard Mate Compatible ? Guard Mate Compatible Guard Mate holes are built into the noses of certain types of Oregon guide bars and allow the attachment of a Guard Mate tip guard to help reduce the risk of kickback.	No
Tail Mount	A041
Guide Bar Code	DGE
File Size	5/32"
Bar Part Number	140DGEA041
Bar Nose Radius	Small
Sprocket Nose Tooth Count	7

Specifications, Details & Support

Product Description

This 14" guide bar and chain combination features a 3/8" low profile chain that is ideal for homeowners and occasional users who want a low-vibration, low-kickback saw chain. The Chamfer Chisel cutters offer outstanding performance and are durable, easy to maintain and forgiving.

Product Details

Fits Craftsman, Echo, Poulan and others, for additional fit information please see the part finder.
Lubritec™ keeps your chain and guide bar oiled for less friction and longer life
For saw sizes up to 42 cc
Pitch: 3/8" low profile, Gauge: .050", chain drive link count: 52
This bar accepts Guard Mate® tip guards.
Saw chain met the kickback performance requirement of ANSI B175.1-2012 when tested according to the provision s of ANSI B175.1-2012. Low-kickback saw chain meets the kickback performance requirement of CSA Standard Z62.3
WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov

General
Volume	177.321 in³
Product UOM	Each
Weight (with Packaging)	1.595 Lb

Support
Low kickback Saw Chain Warning